Post time: 13-07-22Electric galvanized wire direct selling is in the plating tank through the current one-way to gradually zinc plating on the metal appearance, the production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust. Compared with hot dip galvanizing, the production cost of electric galvanizing is lower. The difference between cold galvanizing and hot galvanizing: the difference between cold galvanizing and hot galvanizing is that the amount of zinc is different. They can be identified from the color. The color of cold galvanizing is shiny silver white with yellow. Hot dip galvanizing shiny white.
- The coating of electrode plays a very important role in the welding process. If adopting the light of the coated electrode welding, is in the process of welding, oxygen and nitrogen in the air can invade the molten metal, the metal iron and beneficial elements carbon, silicon, manganese oxide and nitride oxide and nitride formation, and remain in the weld, weld slag or crack. And melt into the molten pool in the gas can make the weld produces a large number of pores, these factors can make the mechanical properties of the weld is greatly reduced, at the same time to make the weld brittle.
Post time: 04-01-23Coping methods we also have: 1, gouging, the straight wire rolled into a wavy shape, but still not enough to raise chickens with mesh can only be large enough to extend the beak can not feed! 2, is the electric welding net, with the current to wire spot welding together, mesh is not limited.
- At present, some manufacturers also use the process of sandblasting equipment for wire pretreatment, sandblasting process is carried out in the sandblasting room, but in the process of sandblasting, dust will permeate the whole sandblasting room, produce a lot of dust that is not easy to collect, and if the dust will be discharged at will.
Electro galvanizing shaft wire direct is in the electroplating tank through the current unidirectional zinc gradually plated on the metal surface, production speed is slow, uniform coating, thin thickness, usually only 3-15 microns, bright appearance, poor corrosion resistance, generally a few months will rust. Compared with hot dip galvanizing, electric galvanizing has lower production cost. The difference between cold galvanizing and hot galvanizing: the difference between cold galvanizing and hot galvanizing is that the amount of zinc is different. They can be identified from the color. The color of cold galvanizing is shiny silver white with yellow. Hot dip galvanized shiny hair white.
Features: Strong flexibility, good plasticity, a wide range of uses process: selection of high-quality low-carbon raw materials, after drawing, annealing processing, soft and strong tensile resistance. The finished product is coated with anti-rust oil, not easy to rust, can be bundled according to customer requirements, each bundle is 1-50kg, can also be made into U wire, broken wire, etc., plastic inside and linen outside packaging, mainly used for binding wire, construction wire, etc.
Post time: 06-02-23- The surface coating of galvanized wire can be seen whether the quality of galvanized wire is good or not. If the strength of zinc attached to the wire is very poor, then this galvanized wire do not buy, because this galvanized wire must be poor galvanized wire. High quality galvanized wire in general, the zinc layer attached to the surface of the wire is relatively thick, so when we buy galvanized wire, as long as we look at the thickness of the zinc layer, we can generally judge the quality of galvanized wire.
Post time: 20-12-22Annealed wire is mainly made of soft iron wire through low carbon steel heating, hot drawing, constant temperature and other processes. Because of the differences in use, there are also different in the production process, and the specifications are varied. Annealed wire can be widely used, mainly because annealed wire and other kinds of wire, has many advantages.
Post time: 12-04-233. Quality test report
The quality of hot-dip galvanized barbed wire is only good in the surface of the wire attached to the galvanized layer, and with the chemical reaction, the surface of the zinc layer will gradually lose effect because of the oxidation reaction, this situation is more prominent in the humid area of the environment. And because after all, it is rusty iron wire, so the quality of hot-dip galvanized barbed rope is certainly not up to the level of stainless steel barbed rope.
- The disposal characteristics and advantages of galvanized hook net, two kinds of disposal methods of galvanizing: cold plating and hot plating, are better than the anticorrosion corrosion prevention and rust prevention disposal of dip plastic, so the service life is much longer than the dip plastic hook net. Full cover galvanized can also control the cost of consumption, stop a large range of large quantities of galvanized.
- 2, line diameter, mesh spacing (refers to the edge of the twist to the opposite side of the distance).
Post time: 10-03-23Wet air in rain and snow climate, steel mesh sheet exposed, easy to rust, to avoid affecting the use of steel mesh, it is necessary to carry out simple rust prevention treatment, of course, slight rust float will not affect the use of steel mesh. Common network site storage, rainy days, heavy snow, rainy days and rainy days, how to better save the steel mesh, this is a lot of friends need to consider.
Hot dip galvanizing of steel plate is also called hot dip galvanizing. Zinc ingots are melted in the tropics and some auxiliary materials are added in hot dip galvanizing. The steel grid parts are then soaked in a galvanizing tank and a galvanizing layer is attached to the steel plate. The strength of hot dip galvanizing depends on its corrosion resistance, and the adhesion and hardness of galvanized sheet are better. The amount of galvanized steel plate after galvanizing. So this is the general amount of zinc.
Hot dip galvanized iron wire using high quality carbon structural steel, after drawing, galvanized iron wire processing. Hot-dip galvanized iron wire is widely used in the manufacture of wire mesh, highway guardrail and construction projects. With thick coating, corrosion resistance, strong coating characteristics. And according to the special needs of users, according to the industry standard to provide various specifications of galvanized wire.
After annealing, the wire will become soft, flexibility will increase, iron is a relatively active metal, and more active than hydrogen, so it is a good reducing agent. At room temperature, iron is not easy to react with oxygen, sulfur, chlorine and other non-metallic elements in dry air. Its production cost is lower, its use and scale are also relatively wide, and it has better protective function. Therefore, it is an important material for steel parts in strict working environment.
Cold galvanized wire refers to a process in which ordinary steel wire is treated by cold galvanized and a zinc layer is attached to its surface. Cold galvanized wire has the advantages of anti-corrosion and anti-wear, and is widely used in construction, machinery, automobile, electronics and other industries. The following will introduce the production process and flow of cold galvanized wire.
Post time: 16-12-22Two is to pay attention to the storage and use of galvanized wire products, according to the actual environmental standards to choose different specifications of galvanized wire products;
Twist flower hexagonal network customized quotation needs to provide the following parameters:
Post time: 29-05-23