Strength of galvanized wire: tensile strength is the great tensile stress that the material can withstand before tensile fracture; Yield strength has two indexes: upper yield and lower yield. It is a process in which the stress does not increase but the deformation continues to occur during the tensile process. When the force value drops for the first time, the major stress is the yield strength, and the yield strength must be less than the tensile strength.
The spring steel wire is made of high carbon and high quality carbon structural steel or carbon tool steel wire rod, and its chemical composition, gas content and non-metallic inclusion must be strictly controlled according to the use of the spring. In order to reduce the appearance of shortcomings and decarbonization layer, the consumption of rod billet to stop surface grinding, if necessary, but also stop peeling.
Galvanized iron wire is widely used in construction, handicrafts, wire mesh, highway guardrail, product packaging and daily civilian and other fields.
2, hot plating wire plating after processing
Post time: 04-01-23Large coil galvanized wire in the zinc immersion distance debugging, keep the original speed unchanged, according to t= KD to determine the zinc immersion time (1), where: t is the zinc immersion time is constant, take 4-7D is the diameter of steel wire mm, and then estimate the zinc immersion distance. By adjusting the zinc dip distance, the zinc dip time of steel wire of various specifications can be shortened by 5s on average. In this way, the zinc consumption per ton of steel wire decreases from 61kg to 59.4kg.
- In cow pen net there are generally pvc covered plastic pvc covered plastic is in the original galvanized steel wire coated with a layer of dark green or gray brown plastic mold, to avoid the corrosion of wire diameter, conducive to the improvement of the corrosion and rust prevention function of wire diameter. So the better the material, the higher the price. Zinc-aluminum alloy cattle net is the best metal net on the market, the price is higher than hot dip galvanized raw materials. The service life is about 80-90 years, and the anti-corrosion function is excellent.
Post time: 19-10-22Black iron wire application in the process, the main is through the hot metal billet rolling into six point five mm wire rod, and then put it in the drawing into a line of different diameter, the plant and then gradually narrow drawing plate aperture, cooling and annealing, plating process, such as making a variety of different specifications of the wire, the wire compared with ordinary black iron wire, will be more softer, The softness is also very uniform, the color is consistent, widely used in the construction industry, mining, chemical industry, welding mesh, welding hanger, reprocessing industry, etc.
- Galvanized iron wire is divided into hot galvanized wire and cold galvanized wire, using low carbon steel wire processing, after drawing molding, pickling rust removal, high temperature annealing, hot galvanized, cooling and other processes. It has good toughness and elasticity, and the amount of zinc can reach 300 grams/square meter. It has the characteristics of thick galvanized layer and strong corrosion resistance. Galvanized iron wire can be cut off in the construction of the tie wire, the length of 20cm, 30cm and 40cm, can be cut off according to requirements.
- The material of wire mesh can choose galvanized wire, stainless steel wire, copper wire, coated wire, lacquer wire, etc., different materials are used in different fields, such as construction, culture, decoration, etc.
- Although galvanized hook mesh is outstanding because of its surface, this does not mean that this hook mesh product is not useful. From the point of view of people’s use of it, this hook mesh products through a surface of galvanized treatment, whether it is wind and sun, or man-made inadvertent damage, will not bring a little harm to it, so the more comprehensive use of galvanized hook mesh products will then be widely used in several fields.
- The screen is made into a box-like container, with stone filled with cages, can be used to protect and support seawall, hillside, road and bridge, reservoir and other civil engineering, flood control and flood resistance is a good material.
- No less than 5 disks should be extracted from each inspection lot for diameter error inspection. 1 point of steel wire should be extracted from each disk to measure steel wire diameter, and the actual diameter of steel wire at this point should be taken as the average value of the two vertical directions. The diameter error of cold-drawn low carbon steel wire should conform to the rules in the table below. The unqualified inspection batches shall be checked one by one, and the qualified batches can be used for engineering.
Enclosure to calculate the use of barbed rope, so as to reasonably plan to purchase the amount of barbed rope to facilitate construction
The basic thing to choose a pet carrier is to be able to stand up straight inside it, so that your pet can be comfortable, but also need to be able to stretch out all four feet when lying down. Think of your pet as a person, and give it a larger cage where it can move around on one side and sleep on the other. You can use an old blanket for cushions in your pet’s cage, or buy special cushions for pets, as long as they are comfortable.
- 3. Scope of application. Electrogalvanizing involves more and more extensive fields, fastener products have been widely used in machinery manufacturing, electronics, precision instruments, chemical industry, transportation, aerospace and so on in the national economy is of great significance.
- The application range of small hexagonal net is also relatively wide, can be used for building wall fixed insulation layer, pipeline, boiler fixed insulation, decoration and other fields.
- Twisting hexagon mesh production factory is the selection of low carbon steel silk woven, mesh structure he has corrosion resistance, high strength and ductility and so on. The diameter of steel wire can reach 2.0mm-4.0mm. The surface of steel wire is usually used for hot-dip galvanized maintenance. The thickness of galvanized maintenance layer can be made according to the needs of customers.
Hot dip galvanizing, also known as hot dip galvanizing, is a method of obtaining a metal covering layer by immersing a steel member into a molten zinc solution. With the rapid development of high-voltage power transmission, transportation and communication, the protection requirements for steel parts are becoming higher and higher, and the demand for hot-dip galvanizing is also increasing. Usually the thickness of electrogalvanized layer is 5 ~ 15μm, and the large roll galvanized wire layer is generally more than 35μm, or even up to 200μm. Hot dip galvanized coating ability is good, dense coating, no organic inclusions.
Compared with other galvanizing processes, the cleaning requirements for low carbon steel wire before galvanizing are low. However, under the current trend of increasing the quality level of galvanized layer, some pollutants brought into the plating tank are obviously harmful. Because cleaning galvanized coating wastes a lot of time and reduces the production, it is very important to properly clean and effectively rinse the substrate before electroplating.
Sodium and magnesium contain less combustible impurities, and when extinguished, they simply glow. Galvanizing belongs to the electrochemical processing process which is widely used on the surface of steel. So it is, first of all, because zinc coating (especially after supplementary processing, such as chromate treatment and phosphating) resistance to atmosphere and water is more stable, and the galvanized process itself this is cheaper and simple.
Our country industry chooses the low carbon steel with good quality as raw material, and then produces the quality galvanized iron wire by drawing, galvanizing and other processes. Now the production technology of galvanized iron wire products can be divided into hot plating and electroplating two kinds of methods. No matter which one is chosen, it should be carried out in accordance with the corresponding operating specifications, so as to better ensure the production of good products. For key and important parts with tensile strength greater than 1034mpa before plating, the stress should be released at 200±10℃ for more than 1 hour and 140±10℃ before plating.