...
2025-08-14 14:16
737
...
2025-08-14 14:03
2382
...
2025-08-14 13:29
2393
...
2025-08-14 12:35
2302
...
2025-08-14 12:33
356
...
2025-08-14 12:18
656
...
2025-08-14 12:16
385
...
2025-08-14 11:56
2742
...
2025-08-14 11:52
2073
...
2025-08-14 11:50
2611
- - Easy installation - Submersible pumps are relatively easy to install since the motor and worm gear are a single unit.
- Dry Installation
- Slurry pumps are usually larger than standard pumps, have more horsepower and use stronger bearings and shafts. The most common >type of slurry pump is the centrifugal pump. These pumps use a rotating impeller to move the slurry, similar to the way aqueous liquids pass through a standard centrifugal pump.
- Slurry Pump
- Dredge Pump Features
- Some models can generate discharge pressures up to 260 ft. (80 m).
- Determine the perfect combination of slow pumping (to reduce wear) and fast pumping to prevent solids from settling and clogging.
- - By increasing the size of the worm housing, the speed at which the media moves is reduced. This lower velocity translates into lower wear.
- Pump selection for FGD
- >Slurry Pump vs Mud Pump
- In a subsea installation, the slurry pump runs directly in the slurry and does not require a support structure, which means it is flexible and easy to install. If possible, the catch basin should be equipped with sloping walls to allow sediment to slide down into the area directly below the pump inlet. Agitators should be used when the liquid contains large amounts of solids and has a high particle density. Freestanding or side-mounted (submersible) mixers are an excellent choice for resuspended solids, especially if the catch basin is large or does not have sloping walls.
- Slurry Pump
- Slurry Pump
- The Company Adopts Advanced Computer Aided Engineering Software
- Aier Machinery's team of consultants are on hand to provide you with a solution to your needs. Whether you are planning to purchase a slurry pump or need spare parts for an existing pump, we will help you determine your needs and provide advice on fine-tuning your equipment to your specific application.
- - Portable and low maintenance - There are no long or exposed mechanical shafts between the motor and worm gear, which makes the submersible pump more portable. In addition, because there are no long or exposed mechanical connections between the motor and worm gear, less maintenance is required and operating costs are significantly lower.
- Slurry Pump
- High head (i.e. the height to which the pump can move the liquid)
- Slurry Pump
- The construction aggregate industry conveys all forms of slurry, from fine sand to coarse aggregates.
- BCT Ceramic Slurry Pumps
- Slurry pipe diameter.
- Another way of classifying the type of slurry pump installation is dry installation or wet installation. Dry installation pumps have the hydraulic end and drive located outside the liquid, whereas wet installation pumps (such as submersible pumps) operate within a catch basin or slurry. Submersible pumps do not require much support structure and therefore do not take up much space. Depending on the type of operation and installation required, the preferred method of pump installation is determined.
- Consider the impeller. Slurry pumps must have thicker vanes than water pumps to prevent wear. Due to the increased thickness, there will be fewer vanes, otherwise the passages will be too narrow and will affect the performance of the pump. The impeller should have a large enough passage so that the largest solid particles can pass through without clogging.
- Fewer and thicker vanes on the impeller. This makes it easier for solids to pass through than the 5-9 vanes on a standard centrifugal pump - usually 2-5 vanes.
- Slurry Pump
- The Mud pumps need to be equipped with auxiliary equipment, but slurry pumps not. They often need to use with high-pressure water pump when mud pump working. The high-pressure pump sent the water that larger than the mud pump pressure to the leakproof packing. Then protect the packing. Otherwise, it is easy to make the seal part wear. But the wear-resistant slurry pumps can complete the transportation work independently, which not need to equip other auxiliary equipment.
- how-does-a-dredge-pump-work
- WL Series Light-duty pumps are cantilevered, horizontal centrifugal slurry pumps. They are suitable for delivering low density slurries for metallurgical, mining, coal and building material departments. The shaft seal adopts both gland seal and centrifugal seal.
- Working principle
- >Slurry Pump vs Mud Pump
- Slurry Pump
- Consider the pump components
- How does a dredge pump work?
- Selecting the right pump for slurries is critical to get the most bang for your buck. Basic pump components, such as the impeller size and design, material of construction, and discharge configurations must be considered to ensure the pump will hold up against the wear caused by an abrasive slurry. Slurry pumps are generally larger in size when compared to low-viscosity liquid pumps and usually require more horsepower to operate because they're less efficient. Bearings and shafts must be more rugged and rigid as well.
- Aier is pumping experts and offer some useful tips to maintain your >slurry pump.
- Applications of Rubber Lined Slurry Pumps
- Slurry Pump
- Slurry pumps with rubber lining are the ideal pump for the mineral sand industry. They have a special rubber lining that makes them heavy duty pumps capable of withstanding high levels of abrasion.
- Aier Machinery Hebei Co., Ltd. is a large-scale professional >slurry pumps manufacturer, gravel pumps, dredge pumps, sewage pumps and clean water pumps in China.
- Compared to standard centrifugal pumps, centrifugal pumps optimised for slurry pumping usually have the following features.
- Carbon transfer
- Compared to standard centrifugal pumps, centrifugal pumps optimised for slurry pumping usually have the following features.
- Selecting the right pump for slurries is critical to get the most bang for your buck. Basic pump components, such as the impeller size and design, material of construction, and discharge configurations must be considered to ensure the pump will hold up against the wear caused by an abrasive slurry. Slurry pumps are generally larger in size when compared to low-viscosity liquid pumps and usually require more horsepower to operate because they're less efficient. Bearings and shafts must be more rugged and rigid as well.
- As described below, there are several , types of pumps, that are suitable for pumping slurries. However, before considering which technology to use, we must address several key issues.
- Dredge Pump
- >Slurry Pump
- >Slurry pump impeller is one of the most important parts of centrifugal slurry pumps. Depending on the application, slurry pump impeller selection is crucial to slurry pump performance. Slurry applications can be especially hard on the impeller of slurry pumps because of their abrasive nature. In order slurry pumps operates efficiently and stand up to the test of time, impeller has to be selected properly for slurry pumps.
- Capacity: 5-30000m3/h, Head: 5-120m. The company can produce different materials including High
- Make sure you follow the basic rules of pump piping.