- The color of powder coating is divided into: razor wire blue, grass green, dark green, yellow. Plastic-sprayed blade gill net is made of hot-dip galvanized steel plate or stainless steel sheet stamped out of sharp knife sheet, high tension galvanized steel wire or stainless steel wire as core wire combination of resistance devices. Because the shape of the barbed rope is not easy to contact, so it can reach an excellent protective barrier effect. The primary raw materials of products are galvanized sheet, stainless steel plate, high quality low carbon steel wire (electric galvanized, hot galvanized, plastic coated, plastic spraying) wire, blue, green, yellow and other colors.
- Hook net raw materials are basically low carbon steel wire, stainless steel wire and aluminum alloy silk woven, and what are the characteristics and use of these raw materials? Low carbon steel wire is actually the wire we usually use, plasticity is good, good patience, pull is very good.
① The diameter of galvanized iron wire for drawing shall not be less than 4mm, and the diameter of galvanized iron wire for binding shall not be less than 2.6mm.
Iron products are common metal products in life. Iron products appear everywhere in our life, but there is a big problem in using iron products. Iron products will rust, and when rust occurs, it will affect the use and appearance of iron products. Adding non-metallic coating: clean, dry and coat the surface of iron and steel products with a layer of protective materials, such as oil, mineral grease, rust-proof grease, plastic and lacquer.
- Specifications: According to customer demand compressive strength: 122MPa
The height of the shield should not be less than two meters. The length of the shield should be the width of the journey and the extension 10 meters away. The vertical load of the handrail on the bridge is 1.2KM/m, and the horizontal external load is 2.5KM/m, both of which should be calculated separately. Galvanized hook mesh belongs to a hook mesh, it is the selection of galvanized wire, hot-dip galvanized wire as raw materials, woven through the hook mesh truncated.
Friends in the industry know that galvanized iron wire has two kinds of cold galvanized iron wire and hot galvanized iron wire, so what is the difference between cold galvanized iron wire and hot galvanized iron wire? Which is good?
Cold galvanized, generally speaking, do not need heating, galvanized amount is little, this galvanized parts are easy to fall off in wet environment. Hot dip galvanizing, also known as hot dip galvanizing, is to melt the zinc ingot at high temperature, put some auxiliary materials in, and then dip the metal structural parts into the galvanized groove, so that the metal members are attached to a layer of zinc layer. The advantage of hot dip galvanized is that its anticorrosion ability is strong, the adhesion and hardness of galvanized layer is better.
1. Zinc pot operators must stick to their posts
① The diameter of galvanized iron wire for drawing shall not be less than 4mm, and the diameter of galvanized iron wire for binding shall not be less than 2.6mm.
- The galvanized requirements of the parts to be plated: the surface of the parts to be plated should be smooth, and there is no dirt that cannot be removed by pickling method. Such as paint, grease, cement, asphalt and excessive rotten harmful substances; All welds of welded components shall be sealed without air; Pipe fittings and containers must have exhaust and zinc inlet holes; The workpiece should be finished welded steel pipe without thread, if any thread should be protected.
- Cold galvanizing, also called galvanizing, is the steel wire placed in the plating tank, through the one-way current to make the metal surface slow galvanized, zinc is slow, and the thickness is only one tenth of hot dip galvanizing, zinc layer is thin, so the rust resistance is not good, placed in the outdoor usually a few months will rust, applied in the outdoor generally in the plastic coating.
Post time: 03-04-23
Post time: 23-03-23- Annealing is to restore the plasticity of wire, improve the tensile strength of wire, hardness, elastic limit, etc., the wire after annealing is called annealing wire. In the production process of annealing wire, it is very important to ensure the quality of the finished wire, make the wire have certain strength and suitable degree of soft and hard. The annealing temperature is between 800 ℃ and 850℃, and the length of furnace tube is lengthened appropriately for enough holding time.
- Especially after passivation of galvanized layer, the surface of the oxide layer is thicker and compact, itself has high oxidation resistance. On the other hand, when the surface of the galvanized layer is damaged, exposing the inner iron matrix, because zinc is more active than iron, zinc will bear the role of sacrificing zinc anode, zinc will be oxidized before iron, so as to protect the iron layer will not be damaged.
Post time: 01-06-23The distance between the adjacent two thorn rope installation do not know whether you have noticed? Careful observation can find that its spacing is not the same, the thorn rope factory for customer consultation when asking the installation height of the reason.
The quality of hot-dip galvanized barbed wire is only in the surface of the wire attached to the galvanized layer, and with the reason of the chemical reaction, the surface of the zinc layer will gradually lose its role because of the oxidation reaction, this situation is more prominent in humid areas. And because after all, the steel wire will rust, so the quality of hot-dip galvanized barbed wire is certainly not up to the level of stainless steel barbed wire.
- 1, prepare disinfection dog cage utensils: small brushes, old toothbrushes, latex gloves (can effectively prevent corrosive pure disinfectant damage to the skin), birdish, and household commonly used disinfectant.
- In general, when exporting and exporting, the blade thorn rope will be packaged and sold, so that the volume occupied in the container is relatively small, which can be easily placed and will not occupy much place.
- Decorative hook mesh welding, generally more robust, but assume that the workers are new, scheduling machine skills are not high, it will appear to open the solder joint. Once this situation is presented, it will bring significant losses to customers and factories.
Now it is more used in the binding of the construction industry. Compared with ordinary wire, it is also softer and has better luster. Use in daily life does not need to carry out maintenance and maintenance, saving a lot of time, but also save the cost of maintenance and maintenance. Annealed wire has good stability, good corrosion resistance, greatly prolonging the service life. There are many kinds, which can be selected according to different uses. The device for making annealed wire is simple, and the utilization rate of the device is improved. The material properties of annealed wire can meet different processing needs.
Flood control and flood is good information. Can also be used for handicrafts manufacturing, machinery and equipment of transport network mountain beautification network – high strength wire grille (hook flower net, rhombus net) the use of mountain flowers network protection principle, hook flower net, mesh uniform, flat surface, weaving concise, crochet, beautiful generous, wire mesh, mesh with wider picture, diameter of thicker, not easy corrosion, taking a long, and strong usefulness.
- ③ The galvanized iron wire shall not be damaged when it is tightened.