Post time: 23-06-22Now the pet cage on the market is still mainly wire cage, so the identification of wire cage mainly has the following parameters:
The corrosion or discoloration of galvanized iron wire in the atmosphere caused by oxygen, moisture and other pollution impurities is called rust or rust. After galvanized iron wire rusting, it will affect the appearance quality, seriously affect the use, and even cause scrap, so galvanized iron wire must be properly kept and pay attention to rust prevention.
Galvanized iron wire can be divided into hot-dip galvanized iron wire and cold galvanized iron wire according to different processing methods. Galvanized iron wire is more prominent in its corrosion resistance. Galvanized iron wire has good toughness and elasticity, the amount of zinc can reach 300 g/square meter, with thick galvanized layer, strong corrosion resistance and other characteristics. Galvanized iron wire products are widely used in construction, handicrafts, wire mesh preparation, the production of galvanized hook mesh, wall mesh, highway guardrail, product packaging and daily civilian and other fields.
- Barbed wire, on the one hand, is a great protection against livestock theft, because the surface is covered with sharp spikes that make it very difficult to penetrate through the barbed wire. On the other hand, because livestock generally have the habit of bumping, the barbed rope is used to circle, which makes the livestock dare not rush to collide with the barbed rope, so as to save the use cost of users.
Raw material of wire mesh sheet cold drawn low carbon steel wire base material can choose low carbon steel hot rolled disk bar or hot rolled smooth steel bar. The base material number and diameter of cold-drawn low carbon steel wire can be confirmed according to the rules in the table below. During the cold drawing process, the surface shrinkage rate of each drawing should not be greater than the wire mesh before cold drawing. Annealing shall not be carried out during wire drawing. If butt welding is required, the same production unit and base material of the same number should be selected. The appearance quality of wire mesh should not affect wire drawing. When the welding function is poor or brittle fracture occurs, special inspection should be carried out according to relevant standards.
- Zinc coating on steel and ferrous metal plays an anodic role, it is commonly used for those parts subjected to atmospheric or water action, but zinc coating only when the water temperature below 60℃, the anode properties. When the temperature is higher, the potential changes and the zinc to iron becomes the cathode. Therefore, for parts subjected to hot water (such as steam boilers), the zinc skeleton must be approximately 70 microns thick and void free. For parts subjected to low or normal temperature or atmospheric action, zinc coating without pinholes is not necessary.
- 4, according to the wire diameter thickness to adjust zinc dipping time
Post time: 15-02-23
Post time: 11-11-22- In the processing of stainless steel barbed wire after cold galvanized or hot galvanized coating on the surface of the last zinc material, not only beautiful but also plays a good protective role.
- 3. Gently rub soapy water on its body and scrub gently with a towel. Make sure you don’t get anything in his eyes or it might scare him into attacking you (he might show his little fangs and claws).
- The electrolytic deposition of large roll galvanized wire zinc-chin layer is basically the following two kinds of electrolyte: zinc is mainly in the form of zinc cation hydration in the solution; Zinc is mainly present in solution as complex anion. Acid electrolyte belongs to one class, complex cyanide and zincate electrolyte, and nickel sulfate electrolyte constitute the second class. Cyanide electrolyte and acid electrolyte are of great significance.
Welding mesh is also known as external wall insulation wire mesh, galvanized wire mesh, galvanized welding mesh, wire mesh, row welding mesh, touch welding mesh, construction mesh, external wall insulation mesh, decorative mesh, barbed wire, square eye mesh, screen mesh, anti-crack mesh. Stainless steel welding net, is made of high quality stainless steel wire row welding, more acid resistance, alkali resistance, solid welding, beautiful, wide use and so on.
The blade gill net has 3-7 buckles every 2 turns, and it is a circle card. After being opened, it forms a spiral shape. When stretching, you must take protective gloves to prevent scratches. When opening, only one side of the gill net needs to be fixed, and then the gill net needs to be opened in the opposite direction. Pay attention to the spacing of the holes should not be too large, otherwise it will affect the aesthetic effect. As long as the time to slowly return to the line, simple operation, convenient construction.
Post time: 31-01-23Did not do the adhesion test of powder spraying or fluorocarbon spray on the packaging galvanized wire, but there are two points for reference: one, in the sealed or air circulation environment, non-metallic volatiles can corrosion zinc coating; Second, zinc above 230 degrees (c) will brittle the base metal. After powder spraying and fluorocarbon spraying, it is necessary to bake at a higher temperature and in a sealed environment, causing rapid corrosion of zinc, resulting in loose corrosion film resulting in decreased adhesion of coating, and even leading to brittle situation of steel wire.
- 2, galvanized wire mesh molding sheet storage ground should be flat, according to the symbolic requirements of the accumulation of regular, height should not exceed 2M, and away from heat sources, avoid exposure.
Decorative hook mesh selection of stainless steel, aluminum alloy, brass, copper and other alloy materials, through the special process of preparation of hook mesh. It is a silk screen made of decoration. Today we introduce the aperture and wire diameter of the decorative hook mesh.
- The form of installation: in the top and the cage tied together at least should be like the stone cage net that is closely combined not easy to use bad. If the local dressing is suitable, the stability of the structure can be increased. There are a lot of mesh edge method, if the stone cage net only hook in the cage edge and not compiled in the cage edge, even in relaxation.
Hot dip galvanizing is dipped in zinc liquid melted by heating, with fast production speed and thick but uneven coating. The market allows a low thickness of 45 microns and a high of more than 300 microns. The color is dark, the consumption of zinc metal is much, the formation of infiltration layer with the matrix metal, the corrosion resistance is good, and the outdoor environment of hot dip galvanized can be maintained for decades. Application range of hot dip galvanizing: because the coating is thicker, hot dip galvanizing has better protective performance than electric galvanizing, so it is an important protective coating for iron and steel parts in harsh working environment. Hot-dip galvanized products are widely used in chemical equipment, petroleum processing, Marine exploration, metal structure, power transmission, shipbuilding and other industries, in the field of agriculture such as sprinkler irrigation, greenhouse and construction industry such as water and gas transmission, wire casing, scaffolding, Bridges, highway guardrail and other aspects, has been widely used.
- 3, galvanized silk mesh binder transport, storage and use should be in accordance with the relevant provisions to adopt safety, fire prevention methods, so as to be more safe use.
During this process, each time the wire is pulled over, the surface hardens due to the high friction temperature. So basically every time you pull it you have to annealing it in the furnace. On the one hand, it is to reduce the surface hardness. On the other hand, during the process of wire pulling, only the surface is deformed, and the center is unchanged. So there’s a lot of stress inside. Therefore, it is necessary to rely on annealing to eliminate the internal stress, so that the wire becomes soft again to eliminate the stress before being drawn again.
- The blade thorn rope is formed by the punching steel plate and mechanically rolled on the steel wire. The width of the blade is 22mm, the vertical distance between the two blades is 15mm, the longitudinal distance between the blade is 34mm, and the diameter of the core wire is 2.5mm. The blade is made of Q195 steel plate with 0.5mm thickness.